itshrka

L7700 IP Power Supply Controller is an Intercall Nurse call. The L7700 has the capacity to power an entire Intercall system with provision in the enclosure to accommodate a 12Volt 12AH battery for system backup requirements. The unit features an integrated embedded web server used to configure the system configuration, datalog access and remote monitoring. The Ethernet port may be used to connect IP controllers together, provide an interface to other Intercall IP devices and for connection to third party products such as IP/DECT phones & message paging etc. In addition, the unit features; onboard calendar clock and disk drive which records all system activity and configuration settings. Day/Night alarm settings may be automatically switched by the on-board clock or by manual switch. The unit features programmable volt free contact inputs and a volt free contact output together with an RS232 output which can be configured for many baud rate and data formats. The integral float charger supports a single [...]

CMS-IP Call Management Software for L7700 IP Power Supply L7700 IP Power Supply is an Intercall Nurse call. The CMS-IP software is used in conjunction with the L7700 IP Controller and displays real time information from the call system. The CMS IP software nterfaces directly with the TCP/IP LAN (Local Area Network) and may be installed on several computers simultaneously on the same LAN. CMS-IP does not require any complicated Com port setup or Importing of Room Text Data or Users as the information is automatically received over the Network. All of the events are stored inside the L7700 IP Controller, so the PC does not even need to be switched on in order to record system activity. With the use of an additional IP L7744 interface, free text messages may be sent to Message Pagers and DECT telephone handsets. The CMS IP software connects to the same Local Area Network as the L7700 L7700 IP Controller. With the use [...]

FJB2 Fused Junction Board FJB2 Fused Junction Board it's an Intercall Nurse call. The FJB2 replaces the earlier FJB1 and provides four ‘spur’ outputs from the network spine with each output incorporating a over current/voltage and reverse polarity protection device. A front panel mounted red/green LED indicates the condition of the internal fuses and continuously monitors the network data signals. Individual fuse failure LED’s are mounted on the reverse of the unit and in the event of a cable fault, on one of the outputs, the ‘spur’ will be isolated without disabling the entire cable network. Input / Output Terminals: Connect to the network spine and can be daisy chaned as shown above. Note: The two Input/Output terminals are not protected or monitored. Output(s)1,2,3,4: Individually fused and monitored network outputs. Fuses: 4 off 315mA (0.315Amp) Anti-Surge 20mm Fuses. Status LED indications: Flashing Green – Network healthy & All fuses ok. Flashing Red – Immediate Network data error. Flashing Red/Green – [...]

The L748 Large LED Display – clearly read at 5 Metres plus The L748 Large LED Display is an Intercall Nurse call ideal where calls need to be clearly displayed. The L748 can be used in several environments including hospital wards, doctors surgeries, health centres and nursing homes. The L748 displays call information with sixteen illuminated characters which can be read at several metres under normal conditions. All incoming calls are numbered allowing staff to prioritize their response and an integral alarm attracts attention while indicating the current alarm priority. The sounder may be configured in a variety of ways to suit the unit's location. When there are no active calls the L748 can be configured to show a fixed message in the same way as the standard displays. Compatible with the Intercall 600 and Intercall 700 systems, the unit may be used to supplement the standard display units, or as the only type of display fitted on a system. [...]

Code Blue Call Point The Code Blue Call Point is an Intercall Nurse call available as an addressable or slave version, and will generate a Code Blue level of call at the Nurse Station Display. This unit features a single gang plastic moulding with Code Blue call button and reassurance LED. The SCB Slave Code Blue call unit wires into the rear terminals of another addressable device such as the L762 Addressable Call Point Display to generate a code blue level of call. Calls are reset upon acceptance at the Nurse Station Display. The L722AN417 Addressable Code Blue unit has its own address to identify the precise location of the calling unit. Calls are reset upon acceptance at the Nurse Station Display. L746AN417 Overdoor Lights with Code Blue indication are available with an additional blue LED to identify active code blue calls. Follow Us on Linkedin Contact Us

HD2 Call / Light Handset HD2 Call / Light Handset it's an Intercall Nurse call, A new plastic moulding to match the same style moulding as the pear push lead. The brightly coloured HD2 has two clearly defined buttons, nurse call push with re assurance LED and a light control button. The light button provides a momentary closing contact, which can be used to trigger an external device such as our Intercall LCU to switch room lights on and off. In order to operate the HD2 light control the call point’s jack socket requires a stereo jack socket modification, the L622HL, L722HL, L752HL, L762HL & SCP/HL all have the suitable stereo fitting Follow Us on Linkedin Contact Us