![\"\u0644\u0645\u0628\u0629](\"https:\/\/www.kyrcompany.com\/ar\/wp-content\/uploads\/sites\/3\/2024\/02\/L746_front__94469.jpg\")
<\/p>\nL746 \u0644\u0645\u0628\u0629 \u0628\u064a\u0627\u0646 (\u0646\u0638\u0627\u0645 \u0646\u062f\u0627\u0621) \u064a\u0645\u0643\u0646 \u0627\u0633\u062a\u062e\u062f\u0627\u0645\u0647 \u0643\u0645\u0624\u0634\u0631 \u0644\u063a\u0631\u0641\u0629 \u0645\u0641\u0631\u062f\u0629 \u0623\u0648 \u0643\u0645\u0624\u0634\u0631 \u0645\u062c\u0645\u0648\u0639\u0629 \u0639\u0644\u0649 \u0631\u0623\u0633 \u0645\u0645\u0631 \u0639\u0644\u0649 \u0633\u0628\u064a\u0644 \u0627\u0644\u0645\u062b\u0627\u0644 \u0642\u0627\u0628\u0644\u0629 \u0644\u0644\u0639\u0646\u0648\u0646\u0629 \u0648\u0644\u0627 \u062a\u062a\u0637\u0644\u0628 \u0627\u062a\u0635\u0627\u0644\u0627\u064b \u0645\u0628\u0627\u0634\u0631\u064b\u0627 \u0628\u0646\u0642\u0637\u0629 \u0627\u0644\u0627\u062a\u0635\u0627\u0644<\/p>\n
The L746 Overdoor light is an Intercall Nurse call may be located above a door or corridor to indicate the status of specific call points. It is fitted with Red and Green LED\u2019s which mimic the re-assurance indicator on the call points. The unit is fully addressable and only connects to the Network.<\/p>\n
The unit features 2 sets of DIL switches, and the unit will respond to any device between the Lower and Higher device address. The unit is available with an integral sounder as L746s.<\/p>\n
Connect to the Intercall 600 or 700 (2 wire) Network. [+, \u2013] OBSERVE POLARITY<\/p>\n
Open collector output active continuously when the alarm is sounding. Note: Rating 12vDC 100mA. Minimum [ON] resistance = 100 Ohms. The OC terminal may be connect
\nto RB1 Relay Board to provide normally open & normally closed volt free contacts.<\/p>\n
Emergency Only Jumper – When fitted, the unit will only indicate emergency calls.<\/p>\n
Nurse Present Jumper – When fitted, the unit will not indicate nurse present status.<\/p>\n
<\/p>\n
These are activated by carefully twisting a 3mm drill bit between the finger & thumb on the required
\nhole to remove the printed circuit pad and breaking the connection.
\nDrill Out 1 = Unit Responds to Attack Only
\nDrill Out 2 = Unit Responds to Emergency Only
\nDrill Out 3 = Unit Responds to Call Only
\nDrill Out 1+2 = Unit Responds to Priority Only
\nDrill Out 1+3 = Unit Responds to Accept & Speech Only
\nDrill Out 2+3 = Unit Responds to Assistance Only
\nDrill Out 1+2+3 & FIT JP2 & NO FIT JP1 = Unit Responds to Isolate Only & O\/C Operates
\nDrill Out 1+2+3 & NO FIT JP1 & JP2 = Unit Responds to Presence Only & O\/C Operates
\nDrill Out 4 = Fr Light Patterns
\nDrill Out 5 = Cell Call Indicator*
\nDrill Out 4+5 = Code Blue Option*
\nDrill Out 6 = Convert O\/C Output to single 1 second pulse.
\nDrill Out 7 = Convert O\/C Output to Pulsed output.
\nDrill Out 6+7 = Standard Call Flashes Green LED.
\n* – Special required to enable this feature.<\/p>\n
The sounder mimics the LCD display sounding patterns. (only applies to L746S)<\/p>\n
Sets the lowest call device address that the light will show.<\/p>\n
Sets the Upper call device address that the light will show. The L746 will respond to all call devices between the lower & upper addresses with the highest level of call. Overdoor light settings may overlap so that more than light will respond to several call points. If the unit is required to respond to a single call point address, set both lower and upper DIL switches to the same address.<\/p>\n
Flush or surface mount in standard \u2018single size\u2019 electrical backbox. (See page 16). Connects
\nto system two core and optional ceiling pull switch and auxiliary devices.<\/p>\n
80 x 80 x 40 mm, 70g.<\/p>\n